Telehandler Silage Cutter Bucket
Key Specifications
DatasheetTS-SC18
Silage Cutter Bucket
- Bucket Capacity
- 1,800 L475 US gal
- Rated Load
- 1,500 kg3,305 lb
- Hydraulic FlowAt 25 MPa (3,630 psi) rated pressure
- 100–120 L/min26–32 US gpm
- Overall Width
- 2,300 mm91 in
Values as listed by the factory.
Mounting Type
Quick Coupler
Product Description
Clean silage blocks for daily feeding
The TS-SC18 silage cutter bucket shears a block out of the clamp face instead of tearing it loose. A clean, firm face lets less air into the clamp, which helps keep the remaining silage in good condition. The bucket holds 1,800 L (475 US gal) and carries the block to the feed passage or a mixer wagon.
It is rated for material up to 1,000 kg/m³ and a load of 1,500 kg (3,305 lb).
Hydraulic flow comes first
The cutting frame needs 100–120 L/min (26–32 US gpm) at a rated 25 MPa (3,630 psi). That is more than many compact machines deliver, so check your flow before anything else; our hydraulic flow guide shows where to find it. For loose feed and grain, a plain agriculture bucket is the simpler choice.
Machines and farm use
Six Telescro telehandlers take this bucket, among them the T735-A agricultural telehandler and the T1035 telehandler. Our agricultural telehandlers page compares the farm models, and the overview of attachments for agriculture shows what else they can run. Compact models with lower auxiliary flow are not on the list for this reason.
Not sure what your machine delivers? Send the hydraulic data from its spec sheet or manual, and we check it against the cutter before you order.
See every bucket and grab in the telehandler attachments catalog.
Variants
Ask us for the bucket weight; it is confirmed with your quotation.
| Part code | Capacity | Notes |
|---|---|---|
| TS-SC18Silage cutter bucket | 1,800 L475 US gal | Overall width 2,300 mm91 in |
Specifications
| Specification | Value |
|---|---|
| Rated load | 1,500 kg3,305 lb |
| Rated hydraulic pressure | 25 MPa3,630 psi |
| Hydraulic flow | 100–120 L/min26–32 US gpm |
| Maximum material density | 1,000 kg/m³ |
| Standard color | Red and black |
Fits These Telescro Telehandlers
Find your Telescro telehandler in the table below.
3.5 t rated load
| Telescro model | Silage cutter bucketTS-SC18 | Notes |
|---|---|---|
| T3507 Telehandler3.5t / 7m | Fits | Within the flow range; cuts slightly slower |
| T735-A Agricultural Telehandler3.5t / 7m | Fits | Within the flow range; cuts slightly slower |
| T1035 Telehandler3.5t / 10m | Fits | Within the flow range; cuts slightly slower |
4–5 t rated load
| Telescro model | Silage cutter bucketTS-SC18 | Notes |
|---|---|---|
| T1440 Telehandler4t / 14m | Fits | Within the flow range; cuts slightly slower |
| TH1840 Telehandler4t / 17.5m | Fits | Pressure relief valve |
| T1850 Telehandler5t / 18m | Fits | Within the flow range; cuts slightly slower |
Fits means it mounts on that model. Ask us means we check your machine and job before you order. The safe working load always depends on the machine's load chart.
Not sure it fits your machine?
Configuration Options
Standard Configuration
- Silage cutter bucket with hydraulic cutting frameOverall width 2,300 mm (91 in)
- Red and black paint finishStandard color
Requirements, Options and Limits
What your telehandler needs, what you can add, and where this attachment should not be used.
Machine requirements
- Auxiliary hydraulic flow of 100–120 L/min (26–32 US gpm)Lower flow within this range cuts more slowly
- Pressure relief valve when your machine's auxiliary pressure is above 25 MPa (3,630 psi)Fitted at order
- Bucket and a load of up to 1,500 kg (3,305 lb) within your load chartCheck at your working reach
Available options
- Coupler bracket to suit your telehandlerSend your machine model and coupler type
Limits of use
- Machines with less than 100 L/min (26 US gpm) of auxiliary flowNot enough to drive the cutter
- Material denser than 1,000 kg/m³Above the bucket's rated density
Hydraulic Requirements
Pressure
25 MPa
3,630 psi
Flow Rate
100–120 L/min
26–32 US gpm
Important Safety Information
Verify the allowable load on the host telehandler load chart before lifting a full bucket. Keep everyone well clear of the cutting frame while it moves, and lower the bucket to the ground before leaving the cab. Depressurize the auxiliary circuit before connecting or disconnecting hoses.
Actual allowable load depends on the host telehandler and its load chart. Always operate within the host machine’s limits.
Interested in this attachment?
Our engineers can help you verify compatibility with your machine and provide customized solutions.
Response Time
Within 2 hours
on business days